车辆自组织网络中新型NP-CSMA随机多址协议研究分析

智能交通的出现使得车辆自组织网络受到越来越多的关注。车辆自组织网络的动态拓扑结构变化非常剧烈,这对网络的吞吐率、传输速率等性能提出了很高的要求。提出1种具有握手机制协议的自适应多通道双时钟NP-CSMA随机多址接入协议。该协议首先区分2种P-CSMA协议,握手机制成功解决了隐藏的终端问题,双时钟机制减少了平均空闲时间,多通道机制增加通道数量和划分用户优先级的同时提高了系统吞吐率,自适应机制能够使系统在高负载下保持稳定吞吐率。还对该协议的传输速率进行了分析,得出该协议的传输速率相对较高的结论。通过平均周期方法推导吞吐率和传输速率的计算公式,仿真结果与理论推导一致。     

Strain-rate dependence of surface/subsurface deformation mechanisms during nanoscratching tests of GGG single crystal

Constant- and varied-depth nanoscratching tests of GGG single crystal were carried out at different scratching velocities. The morphologies of the scratched grooves and chips were analysed using scanning electron microscope. The experimental results indicated that higher scratching velocity led to shallower penetration depth, shallower residual depth, and larger continuous chips. Increasing the scratching velocity could effectively improve the plasticity and reduce the brittle-to-ductile transition depth of GGG single crystal. Based on the contact stress and contact area between the analysed sample and Berkovich indenter, a model for predicting the penetration depth was developed, which took into account the strain rate effect and elastic recovery of materials. The model was verified using constant- and varied-depth nanoscratching tests, and the predicted and experimental results were in good agreement. Subsurface damage underneath the ductile surface was characterised using transmission electron microscope. The TEM results demonstrated that higher scratching velocity led to the slipping planes appearing in more directions, which prevented the generation of long slipping plane and reduced the depth of the damage layers. The plastic deformation of GGG at the scratching velocity of 100 μm/s was dominated by poly-crystalline nanocrystallites and amorphous phases, and was similar to that at the low scratching velocity. This study provided a fundamental understanding of the strain-rate dependence of surface/subsurface deformation mechanisms of GGG during ultra-precision machining.     

物联网环境下基于情境的语义Web服务选择

当前Web服务海量增加，物联网应用技术快速发展、不断普及，而现有的Web服务选择算法低效、用户匹配度低。针对该问题提出一种物联网环境下基于情境的语义Web服务选择方法。该方法应用QoS参数的无量纲化与语义Web服务动态选择方式，将物联网环境下服务与语义Web服务相结合，并根据用户需求针对QoS选择最优的服务集。实验表明，该方法能有效地提高用户服务动态选择的成功率。     

固体碳直接还原钢铁厂含锌固废的理论与实践

 钢铁厂内的含锌固废数量巨大，同时富含铁、碳等元素，是可循环再利用的二次资源。通过固体碳直接还原ZnO和FeO的热力学分析，发现在非标准状态下，ZnO的还原条件要优于FeO。为此，在实验室条件下设计了含锌固废在不同温度和时间下的还原试验，发现在还原温度为1 423 K、还原时间为15 min以上时，脱锌率可达到90%，而铁的金属化率需要在1 573 K时才能接近90%；在还原温度低于1 423 K时，还原时间对脱锌率的影响较大；在还原温度高于1 473 K时，还原温度对脱锌率影响较小，同时脱锌率可达到95%。这些结果对国内当前处理含锌固废主要工艺(回转窑、转底炉)的操作制度设置具有重要的参考价值，也为如何选择合理的工艺路线，以低投入、低运营成本实现含锌固废的再利用提供了理论依据。     

气控环形防喷器密封胶芯大变形分析

针对气控环形防喷器胶芯在密封过程中的大变形以及与油管存在密封压力难以计算的问题,建立胶芯物理模型,结合厚壁筒理论与橡胶本构方程,同时考虑胶芯的材料非线性和几何非线性,探讨防喷器密封过程中胶芯变形与接触压力的变化。根据胶芯变形过程中无变形阶段、自由变形阶段和接触变形阶段的不同受力状况,利用迭代的方法对每个离散微段施加控制压力,得到不同控制压力下胶芯变形量与接触压力,并与仿真结果进行比较。结果表明:在自由变形阶段,随控制压力增加,胶芯变形量逐渐增大且由中间向两侧逐渐减小;在接触变形阶段,胶芯内径保持不变,且与油管间接触压力不断增加。采用胶芯变形理论方法计算的接触压力变化规律与仿真结果基本相同,验证了胶芯变形理论计算方法的正确性。     

Experimental study on flame spread along fuel cylinders in high pressures

Flame spread over solid fuels in high‐pressure situations, such as nuclear containment shells during a pressurized period, has potential to result in catastrophic disaster, thus requiring further knowledge. This paper experimentally reveals the flame spread behaviors over fuel cylinders in high pressures. Polyethylene and polymethyl‐methacrylate cylinders with the diameter of 4.0 mm are used in this study. Ambient gas is air, and total pressures are varied from naturally normal pressure (100 kPa) to elevated pressure (500 kPa). Flame characteristics including flame appearance and flame size and burning rate and flame spread rate are investigated. Results show that in high pressure, the flame appearance is significantly affected. As the pressure increases, the blue flame disappeared, and the color of flame tip changes from luminous yellow to orange as well the orange part extends down towards the base of flame. The dimensionless flame height increases with pressure for pressure below 150 kPa and then decreases with pressure above that level. The burning rates show increasing trend with pressure and are proportional to P^0.6 and P^0.79 for polymethyl‐methacrylate and polyethylene, respectively. Besides, flame spread rates for polymethyl‐methacrylate and polyethylene both were found to be proportional to P^0.5.     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

负径向电场对带电粒子俘获率影响的数值模拟

本文采用数值方法求解Grad-Shafranov方程反演EAST典型长脉冲放电实验(炮号33068)的平衡位形和磁场分布，进而结合粒子在托卡马克电磁场中的运动方程，模拟氘离子在负径向电场存在时的运动轨迹，并统计不同负径向电场下的氘离子俘获率。结果表明：随负径向电场的增大，氘离子轨迹由扩张通行轨迹向外翻香蕉轨迹再向内翻香蕉轨迹，最后向压缩通行轨迹演变；氘离子俘获率随负径向电场的增大而减小，氘离子初始速度越小，其变化越大。     

瞬态闭锁试验在0.13 μm大规模集成电路中引起的潜在损伤

瞬态剂量率辐射试验会引起集成电路发生损伤或失效，其原因至少有两种：闭锁大电流引起的电路内部金属互连熔融；累积电离总剂量引起的氧化层电荷造成阈值电压偏移。本文以一种0.13 μm体硅CMOS处理器为对象，研究了瞬态剂量率和稳态电离总剂量辐射效应规律。结果表明：瞬态剂量率闭锁效应对处理器造成了显著的潜在损伤，导致其总剂量失效阈值从1 030 Gy(Si)降低至600 Gy(Si)。研究结论对于大规模集成电路的可靠性评估和指导辐射加固设计有重要参考意义。     

硫酸体系中锰钽铌矿加压浸出研究

针对单一硫酸体系锰钽铌矿加压浸出下钽铌浸出率均不到10%的问题,在硫酸体系引入助浸剂,考察氟化铵、双氧水、反应压强、硫酸浓度、反应温度、氟化铵矿比对锰钽铌矿加压浸出的影响,采用XRD对浸渣进行物相表征。实验结果表明,在锰钽铌矿加压浸出中,引入助浸剂氟化铵,温度200℃、硫酸浓度50%及氟化铵/矿比为0.8∶1的条件下钽浸出率超过93%,铌浸出率超过96%。引入氟化铵对硫酸体系下锰钽铌矿的加压浸出效果的提升十分显著。